Johns Manville Insulation Removal Nationwide

Johns Manville Insulation Removal in Long Beach: What to Know First

Johns Manville insulation removal in Long Beach typically takes one to two days for a standard attic and most homeowners pay between $1,800 and $4,200 depending on square footage, insulation type, and how much of it has to come out. We’re an independent Johns Manville service provider, not a manufacturer dealer, which means we quote the removal honestly and stand behind the work in writing for 365 days. This page is for Long Beach homeowners who know they have Johns Manville product in their attic, walls, or crawlspace and need it pulled out properly. Call (562) 317-6204 for a free estimate, and a live person will answer.

Call (562) 317-6204

How Johns Manville Products Fail – and How We Fix Them

Johns Manville makes a broad range of insulation, and over the years we’ve seen specific failure patterns in Long Beach homes that differ from what other brands do. Here’s what we run into most often.

• Johns Manville fiberglass batts in older beach bungalows: The kraft-paper facing on JM ComfortTherm batts breaks down in Long Beach’s salt air and humidity. The paper turns brittle, the batts slump in the wall cavities, and you end up with dead air pockets where heat and moisture collect. We remove the failed batts, inspect the cavities for mold, and recommend a replacement that holds up to coastal conditions.
• JM Spider loose-fill in cathedral ceilings: Spider insulation was popular in the 1990s and early 2000s for cathedral and vaulted ceilings. The problem is that the fibers settle, leaving a gap at the top of the rafter bay. Once it settles, the R-value drops and you’re paying to heat a void. Extraction requires vacuuming from the attic side, which is exactly what our removal crew does before any re-insulation.
• Johns Manville Attic Protector blown-in fiberglass: Attic Protector is still a common product in Long Beach attics, but when the roof leaks, the fiberglass mat that’s sitting flat against the ceiling drywall acts like a sponge. Wet JM fiberglass compresses and loses almost all thermal value. You can’t dry it out and fluff it back up. It has to come out.
• JM spray foam installations gone wrong: While Johns Manville isn’t primarily a spray foam brand, many Long Beach homes have open-cell JM/Corbond foams that were installed by third parties. A bad ratio from an old rig or a too-thin pass creates a sticky gummy layer that never cures and off-gasses for years. That’s a full scrape-out, and it’s one of the messier removal jobs we do.
• Johns Manville duct board and duct wrap: In older Long Beach ranches, we find JM duct wrap that’s been torn open by rodents, saturated with crawlspace moisture, or compressed by careless plumbers. When the duct wrap fails, the ductwork itself loses integrity and the HVAC system works harder. We strip the old wrap, inspect the ducts underneath, and re-wrap with new material.

Our Johns Manville Insulation Removal Process

Every Johns Manville removal job in Long Beach follows the same disciplined sequence. No shortcuts, no surprises.

1. 1
   You call us. A live person answers, takes the details about your attic or crawlspace, and schedules a walkthrough.
2. 2
   We inspect and measure. Bryce Holloway or one of our lead techs goes up, identifies exactly which Johns Manville product is in place, checks for moisture, mold, pest activity, and wiring issues, and takes square footage measurements.
3. 3
   You get a written price. Before any tool comes off the truck, you have a line-item quote in your hand. The number you approve is the number on your invoice, full stop.
4. 4
   We remove and contain. Crews run commercial HEPA-filtered vacuum equipment, bag the old insulation, and seal the work area to keep dust out of your living space. We don’t drag bags through your hallway.
5. 5
   We clean and inspect. After the removal, we check the sheathing, wiring, recessed lights, and venting. If we find a problem, we tell you before we leave.
6. 6
   You get the 365-Day Done Right Promise in writing. If anything we touched fails within a year, we come back at no charge. No fine print, no call-center runaround.

What Johns Manville Insulation Removal Costs in Long Beach

Here’s what we’ve charged for common Johns Manville removal scenarios around Long Beach over the past few years.

• Attic fiberglass batt removal: $1.25 – $2.00 per square foot of attic floor space. A 1,200-square-foot attic runs $1,500 – $2,400.
• Blown-in fiberglass or cellulose removal: $1.50 – $2.75 per square foot. A 1,200-square-foot attic runs $1,800 – $3,300, more if it’s packed tight or contaminated.
• Spray foam removal (full scrape-out): $4.00 – $8.00 per square foot depending on thickness and condition. This is labor-intensive, and we quote it only after an inspection.
• Wall cavity batt removal: $3.50 – $6.00 per square foot of wall area, because the work is access-driven and slower than attic work.

What moves the price: total square footage, how deep the insulation is packed, whether there’s moisture damage, how tight the access points are, and whether pests left droppings behind. Call (562) 317-6204 and we’ll give you a firm written price after the inspection.

Why Long Beach Homeowners Call Alden Insulation Long Beach for Johns Manville Work

Alden Insulation Long Beach is independently owned and operated, held to The Garrison Standard. That means every job gets a written price before it starts and a written guarantee for 365 days after it’s done. Our techs are background-checked and uniformed, and they arrive inside the scheduled window, not a vague half-day range. We work with eight industry-respected brands, Johns Manville included, plus Reflectix for radiant barrier applications, so we’re not tied to one manufacturer’s product line. We recommend what’s right for the house, not what’s in the warehouse. Calls are answered by a live person 24/7. You’ll never reach a voicemail tree when you call (562) 317-6204.

FAQs